The purpose of building shower curb in the rest room or wash room is to prevent the water flow out to the external floor. It’s act as a shower drain as well, it directs the water to the drain instead of flowing out to the external floor. In this situation, it’s meaning that the shower curb will be contacted with the water, shower curb is built by concrete too, which means in order to prevent the water contacts the concrete shower curb and affect the durability of shower curb, shower curb needed to be protected by some kind of water proofing system.

How To Build Shower Curb

There are several ways and methods to build shower curb, one of the way is using plaster board. The plaster board acts as a wall to prevent the water soaks into the shower curb. It’s kinda simple to build the shower curb with the method of using plaster board. Procedures as below :

1) Assuming that the concrete curb has been done.

2) You have to install the plaster board that has been bought from the supplier.

3) Jointing the plaster board with screws that can be joining with the shower curb.

4) Cutting the extra portion of the plaster board.

5) For the curving shower curb, the plaster board need to be cut in 45 degree that can be joining with the following shower curb.

6) After shower curb has been cut, join them in a suitable length.

7) After the shape has been set, install the plastic board on the shower curb.

8 ) After placing them nicely, secure the plastic board outside the wall of the shower curb by using the galvanized roofing nails.

9) Shower curb with plastic board has done!

Bookmark

Hide Sites

List Of Concrete Curb Equipment – Molds

Here is a list of concrete curb equipment for molds.

1) 5×3 Small Decorative Mold

2) 6×4 Decorative Mold

3) 6×4 Angle Mold

4) 6×4 Round Cap Mold

5) 6×4 Round Cap Lock Mold

6) 6×6 Super Angle Mold

7) 6×6 Super Deco Mold

These are the steel molds that commonly used by the concrete curbing contractor to build concrete curb or concrete landscape edging, it’s easy to be used and short working period needed. The steel mold is not too expensive while contractor can use it for several times until it spoils.

Source : Borderlinestamp

Bookmark

Hide Sites

List Of Concrete Edging Machine

1) PRSting

Features :
i) The curb machine can do compaction nicely with its double drive compactor.

ii) The mold for concrete curb is changeable.

2) RE500

Features :
i) It comes with a single drive compactor that it allows you to do a compaction on the concrete curb and make it look nice and strong.

ii) The mold for concrete curb is changeable.

3) Creative Curb Machine

Features :
i) It’s very light and easy to carry to everywhere.

ii) The machines can either use gas or electric power.

iii) The machines has a orbital pattern and able to cut down concrete waste at the side of the concrete curb, it saves times and works.

4) Edgemaster Series 800 Concrete Curbing Machine

Features :
i) This concrete edging machine able to build up to 300ft concrete edging in a hour.

ii) It’s light and can be operated by one person.

iii) It has gas-powered or electric models.

5) Lil Bubba EP Curbing Machine

Features :
i) This concrete edging machine can be building up to 4.8 metres concrete edging per minute.

ii) It has a 3.8 liters fuel tank, so it can building concrete edging for longer period without filling fuel too frequent.

6) TYGAR ’s Bengal TG1000 Curb Machine

Features :
i) This concrete edging machine able to produce up to 16ft of concrete edging per minute.

ii) It has over 30 different stamp patterns to match brick, slate, stone, and other designs.

7) Borderline Edging Machine

Features :
i) Mould is changeable where you can change to 3 designs of concrete edging.

ii) Easy to operation and environmental friendly.

Sources : Edgemaster | Taylormadeedging | Tygarmfg | Borderline

Bookmark

Hide Sites

This type of concrete curb doesn’t require concrete curbing machine to construct, this type of concrete curb might need to be constructed by hand. Several concrete curb workers might need to be hired and concrete mixer need to be used too. The materials that will be used to construct the curb and gutter forms are concrete, expansion joint filler, curing compound and steel reinforcement bar. The concrete curb and gutter forms will be measured in meter according to Standard of Method of Measurement.

Components of Curb Gutter Forms

The components that used to construct the curb and gutter forms system are slightly different between both types of curb and gutter forms system. The components that will be used for Straight Curb and Gutter setup are front form, nail stake, curb face form, division plate, back form and top spreader. While the components that will be used for Radius Curb and Gutter setup are radius back form, curbface form, full division plate, radius front form, skeleton division plates and form pins.

Types of Curbs for Straight Curb and Gutter Forms

There are 5 basic types of curbs that are used to construct straight curb and gutter forms, types of concrete curb to be used is depending on the situation and location of the curbs to be built.

1) Vertical face – A setup with the front and the back must be in 90 degree angle.

2) Battered face – A curbface with the front and the back must be in somewhere around 90 degree angle.

3) Bottom radius – A battered curbface with a single radius formed into the bottom of the curb.

4) Top and bottom radius – A battered curbface with a radius formed into the top and bottom of the curb.

5) Drive over – A curbface with a slow, gradual batter allowing traffic to pass over.

Source : DeeConcrete

Bookmark

Hide Sites

List Of Concrete Curbing Equipment – Concrete Trowel

There is a list of concrete curbing equipment for Trowel :

1) 4×4 Square Trowel

2) 5×3 Decorative Trowel

3) 5×4 Square Trowel

4) 6×4 Front Angle Half Trowel

5) 6×4 Angle Back Half Trowel

6) 6×4 Angle Trowel

7) 6×4 Decorative Front Half Trowel

8 ) 6×4 Decorative Trowel (Original Style)

9) 6×4 Decorative Back Half Trowel

10) 6×4 Square Trowel

11) 6×4 Square Half Trowel

12) 6×4 Round Cap Trowel

13) 6×4 Round Cap Half Trowel

14) 6×4 Angled Lighting Trowel

15) 6×4 Multi Lighting Trowel

16) 6×6 Square Trowel

17) 6×6 Square Half Trowel

18) 6×6 Parking Lot Half Trowel

19) 6×8 Square Trowel

20) 8×6 Square Trowel

21) 8×6 Parking Lot Trowel

22) 8×8 Half Trowel

23) 8×8 Square Trowel

24) Walkway Trowel

25) Walkway Half Trowel

These are all the types of trowel that commonly used for building concrete curb and concrete landscape edging in shape, concrete curbing contractor can build the concrete curb with the shape they want with relevant trowel. It’s simple to be used and can be constructing a good concrete curb design by following client’s requirement.

Source : Borderlinestamp

Bookmark

Hide Sites